control punch
英 [kənˈtrəʊl pʌntʃ]
美 [kənˈtroʊl pʌntʃ]
网络 控制孔; 标志孔; 控制打孔; 穿标志孔
双语例句
- Template-based code generation method for numeric control punch
数控冲床加工中基于模板的代码实现方法 - Construction Quality Control On Thick Gravel Layer Punch Pile
深厚卵石层冲孔灌注桩施工质量控制 - However, with the development of embedded microprocessors, embedded systems have begun to be used in the numerical control punch automatic feeding system.
而随着嵌入式微处理器的发展，嵌入式系统也开始运用到数控冲床自动送料系统中来。 - The Design of Auto-feeding System of Numerical Control Punch Based on ARM
基于ARM的数控冲床自动送料系统的设计 - Analysis and Elimination of Raised Grain Defect during Fabrication of Numerical Control Small Punch Mesh Plate
数控小孔冲床网眼平板加工中的波浪纹缺陷成因分析及排除 - The auto-induction start system and the punch press linkage ( control punch press start).
自动感应启动系统与冲床联动（控制冲床的启动）。 - The model of the failure probability distribution was obtained by applying total failure time method for the numerical control punch.
运用故障总时间法初步确定数控冲床的故障概率模型。 - Microcomputer-based numerical control system for punch press
基于单片机的冲床专用数控系统的软件设计 - When numerical control punch press processing plate has the pad dregs reason brief analysis
数控冲床加工板材时产生垫渣的原因浅析 - Self-excited noise control for punch press
冲床自鸣噪声的控制 - The Holding Control of the Punch Press Improved by CNC Technology
冲床数控改造的同步控制 - Based on an introduction of the pile foundation construction for the flood dike in city proper of Pingnan county, the author demonstrated and summarized the construction quality control measures for artificial excavating-bore pile and for punch filling pile under relatively complicate karst geological conditions.
通过对广西平南县城区防洪堤桩基的施工，介绍人工挖孔桩及在较复杂的岩溶地质条件下采用冲孔灌注桩施工的质量控制措施，并加以总结。 - The author conducts a complete and detailed theoretical analysis on the causes of raised grain defect during the fabrication of lattice mesh plate in the numerical control small punch spinning drying equipment in the article.
文章就数控小孔冲床加工纺织烘干设备中帘子网眼平板产生波浪纹缺陷的原因，进行了全面、详细的理论分析。 - The paper's important content and production are: ( 1) Set up three-dimensional elastic-plastic FE model for incremental sheet forming. Realize continuous simulation process for incremental sheet forming through imposing time-displacement curve to control its motion on the punch;
建立渐进成形工艺三维弹塑性有限元模型，通过对成形头运动施加时间-位移控制，实现了连续模拟过程； - The method may apply for the noise control of middle and large punch press.
该方法适合于中、大型冲床噪声的治理。 - PLC control properties of two kinds of control scheme for JH23-63 punch press electrical appliances are comprehensively and thoroughly analyzed. Hardware wiring diagram and ladder diagram for the punch press PLC are established.
对JH23－63型冲床新旧两种控制方案进行了全面深入的分析，并建立了PLC硬件接线方案和梯形图。 - Fault Analysis of Numerical Control Punch
数控冲床故障分析 - In the paper, a kind of numerical control high speed punch hydraulic system is designed. It has the characters of simple structure, high stepping frequency, and safety.
本论文开发研制的数控高速冲床液压系统采用比例伺服控制，结构简单、冲压频率高、安全可靠。 - Design of a single-chip control system of rapidly step-wise feed to a punch press
基于单片机控制的冲床旁置快速步进供料系统的设计研究 - Design of PLC-Based Control System of Automatic Feeding Device on Punch
基于PLC的压力机自动送料装置控制系统设计 - Study of NC Automatic Programming for Numerical Control Turret Punch Press Machine
数控转塔式冲床NC自动编程研究 - This paper introduces both free port communication mode of SIMATIC S7-200 series PLC and programming method by applying VC++ 6.0 to realize serial communication between personal computer and PLC in Windows. The upper computer monitoring and control system is developed for glassware punch.
介绍了西门子S7–200系列PLC的自由口通信模式及在Windows环境下应用VC++6.0实现PC机与PLC串行通信的编程方法，开发了玻璃器皿冲压机上位机监控系统。 - : On the basis of briefly expounding traditional relay-contactor control method of the punch press electrical appliances, necessity with the PLC control for punch press is pointed out.
在简述冲床电气传统继电器&接触器控制方法存在问题的基础上，指出了对其进行PLC控制的必要性。 - Design and Simulation of Numerical Control High Speed Punch Hydraulic System
数控高速冲床液压系统设计及仿真 - The hardware equipments of this system includes digitizer, GW-386 micro-computer, console, control mechanism, punch and detector.
该系统的硬件设备包括数字化仪、长城386微机、控制台、控制机构、打卡机和检测机构等。 - Model of failure probability distribution for numerical control punch
数控冲床的故障概率分布模型 - In the paper, the design and realization of small die machining a big hole for numerical control punch press is presented in brief, giving concrete design idea and flow chart of gen-rator.
本文介绍了在数控冲床上应用小模具加工大孔的设计方法和实现途径，并给出了编制软件的具体设计思想和程序框图。 - Software Design Which Small Die Machines Big Hole for Numerical Control Punch Press
数控冲床小模具加工大孔的软件设计 - Research on Electro-hydraulic Control System for High Speed Turret Punch Press
高速转塔冲床电液控制系统研究 - As one of eight kinds of forging press, numerical control punch press is widely used in mechanical, electronics, aerospace, and so on.
作为锻压机床八大类产品之一的数控冲床，广泛应用于机械、汽车、航空、兵器、电子等行业。